How to Replace a Kia Sportage Replacement Key
For many Kia models, the key contains an integrated keyless entry system. This key is similar to the remote control, and can be exchanged with a Kia dealer.
Key fobs may stop working due to various reasons, such as an empty coin battery worn buttons or buttons, signal interference, water damage and a damaged receiver module. Here are some suggestions to help you get your Kia key fob that is a replacement for the sportage once more.
How do you replace the remote key or smart key
The battery in your Kia's intelligent key will eventually need be replaced, whether it's a remote key or a push-to-start one, or a regular metal key that doesn't have an electronic transponder. This is especially relevant if your vehicle shows a message that states the smart or remote keys aren't powered.
It's a simple procedure. In order to replace the battery of the key fob remove the mechanical key from the slit at the back of the key fob and lift the cover. A small screw is found inside the key fob, which holds the battery in place. Take out the old battery by detaching the screw using a small screwdriver. Insert the new battery and then close the opening on the key fob.
Test the key fob by pressing the lock or unlock buttons. If the doors lock and unlock as expected, then you're set! You can now use the hands-free feature to lock and unlock your Kia whenever your fingers feel chilly or when you need to do some errands in Brandon.
Note: Certain key fobs (transponder chip or smart keys) may need to have their programming done. This requires a computer that is available only to the automotive locksmith or dealer. Other keys (non transponder metal keys) are not required for programming. If you want to change the programming of your key, you'll need note the key code's number on the key code tag.
How do I replace a battery
If the Kia key fob doesn't respond when you press the lock/unlock button, it is most likely that the battery is not fully charged. A low battery can also cause other issues, like the check engine light turning on or the engine not turning correctly. Fortunately, replacing the key fob battery is a relatively simple DIY project that requires only some basic tools.
Before starting the process be sure that your vehicle is turned off and all doors are closed. Find the small, metal or plastic piece at the bottom of the key fob. Then, jiggle it until the key comes out. This key can be put into the driver door handle to unlock your car.
To replace the battery in the key fob remove the cover that covers the rear. Utilize a plastic plier tool to loosen up the latch that holds the black negative cable. Remove the old battery, and then align the new battery so that the "+" positive side faces your face and the "negative" negative side is facing the fob's metal electrical contacts. Avoid using too much force when pushing the new CR2032 into place to avoid damaging or breaking the metal contacts.
Once the new battery has been installed after which you turn the key fob off and back on in the ignition for a few times until the door locks cycle. Then you can test your Kia key fob and see if it is working properly again.
How do I replace a smart key
There is a possibility of having a standard keyfob, or a Smart Key based on the model of Kia Sportage. The difference between these is that the smart key comes with a small mechanical key blade tucked inside it, while the standard fob does not. Both kinds of key fobs come with batteries that will eventually have to be replaced. Luckily, this is quite simple and only takes about two minutes.
Be sure to turn off your Kia, and be on a flat well-lit and well-lit area before you begin. Be aware that there are tiny components inside the fob that can fall out if you are not cautious.
The first step is to locate the small release button on the lower backside of the fob. It could be a circular or rectangular slot. After pressing this button mechanical key blade, it will be released and you can then open the key fob.
After the key fob has been opened, remove the old battery. The new battery is a one called CR-2032 and can be purchased through the internet or at a local auto parts shop. After you've finished, you should be able to lock, unlock and start your car with your key fob - even if your engine isn't running!
How do I replace the mechanical key
The Kia key fob is a wonderful option that lets us lock and unlock our vehicle with the touch of the button. As with all devices, the Kia key fob can occasionally have problems. There are ways to solve these issues and keep your key fobs functioning for a long time.
One of the most frequently encountered problems is a dead or dead battery. The fob could be able to stop working altogether or even to stop working intermittently. If this happens you should replace the battery with a new one.
If this doesn't fix the issue you can try using a standard flathead screwdriver to open the fob's plastic casing. Be careful not to damage any internal components or scratch the plastic. Once the battery is removed and replaced, you can replace it with a new one.
Close and open the door using the mechanical key. (Every Kia fob comes with an emergency mechanical key which will fit into the slot). Test kia smart key The Key Lab to check that it's functioning correctly. Contact a dealer, or a locksmith to resolve the problem in the event that the key fob is not working. To avoid lockouts in the future, make sure you get an emergency key that can be able to work with all door and trunk cylinders.